FAQ's
Frequently Asked Questions on Veripos products and services
LD7 Equipment
- I have just changed beams and my station list is not fully populated why is this?
- For LD7 What is the expected latency from one PPS to the NMEA ZDA telegram?
- What is the PPS voltage of my LD7?
- How do I remove satellites from my LD7 (Septentrio GNSS) for DP Trials?
- How do I change my LD7 IP address through USB?
- How do I set my LD7 to output 5Hz on com1 and com 2?
LD4 Equipment
N-Trip
LD5 Equipment
- How do I configure an LD5 to receive RTK corrections?
- How do I tell which version of LD5 I have?
- I have just changed beams and my station list is not fully populated why is this?
- For LD5 What is the expected latency from one PPS to the NMEA ZDA telegram?
- What is the PPS voltage of my LD5?
- How do I remove satellites from my LD5 (NovAtel GNSS) for DP Trials?
LD6 Equipment
- How do I configure an LD6 to receive RTK corrections?
- How do I tell which version of LD6 I have?
- How do i correctly shut down a LD6?
- I have just changed beams and my station list is not fully populated why is this?
- For LD6 what is the expected latency from one PPS to the NMEA ZDA telegram?
- What are the serial pin-outs of the LD6?
Verify-DP Software
GNSS Information
VOSS Support
Verify-DPx Software
LD3 - LD3S Equipment
- I have just changed beams and my station list is not fully populated why is this?
- I have changed my PPP service and my LD3S solution has become unstable, how do I resolve this?
- How do I enable/disable my LD3/LD3S?
- How do I run the VERIPOS L-Band Control software to configure my LD3 or LD3S?
- I need to configure my LD3/LD3S, how do I connect a computer?
- What is the difference between an LD3 and an LD3S?
Product Specification Sheets
GPS
Contacts & Support
Data Formats
Glossary
- GNSS
- Z-Count
- Y-Code
- Temporal Decorrelation
- World Geodetic System 1984 (WGS 84)
- Signal to Noise Ratio (SNR)
General Information
Verichart Software
antenna installation
- How do I install my spotbeam antenna for use in the Gulf of Mexico region?
- How do I install my spotbeam antenna for use in the EAME region?
- What are the Phase Centre values of the V460 antenna?
- What are the considerations with regards to L-Band and GNSS reception when working at high latitudes?
- What tracking dish systems can I use and what Beams will they track?
- When mobilising an antenna what distance is to be from other antenna?
LD2 - LD2S Equipment
- For LD2 What is the expected latency from one PPS to the ZDA telegram?
- What is the PPS Voltage of my LD2 / LD2S?
- What are the tracking capabilities of my LD2 and what services are available to my unit?
- How do I Remove Standard+ Service in my LD2/LD2S?
- I have just changed beams and my station list is not fully populated why is this?
- How do I upgrade the GLONASS option on my Topcon GNSS Receiver?
Veripos Service's
- I have just changed beams and my station list is not fully populated why is this?
- How do I Enable/Disable my VERIPOS hardware?
- What is the difference between terms dual beam, dual constellation and dual frequency?
- What are the ID's of the VERIPOS PPP services (ULTRA, ULTRA2, APEX, APEX2 and APEX5)?
- What is the difference between Apex and Ultra corrections?
- What are the benefits of the Veripos GPS + Glonass Services?
Verify-QC Software
- I have just changed beams and my station list is not fully populated why is this?
- How to load a Verify QC Config onto the LD6 in QC mode?
- What are the new features of Verify-QC v1.20?
- How do I upgrade my verify QC?
- How do I configure an N-Trip RTCM input in Verify QC?
- Tides - How do I convert from MSS Tides to LAT?
coverage charts
- What VERIPOS Reference Stations are available in the African region?
- What VERIPOS Reference Stations are available in the North American region?
- Which beams are available for use in the Americas Region?
- Which beams are available for use in the FarEast Region?
- Which beams are available for use in the Africa Region?
- Which beams are available for use in the Europe and Middle East Region?